Red Deer Carpet Cleaning

Q: I vacuum regularly and we’re careful with spills. 
Why do I need the carpets cleaned? A: Great! Regular vacuuming is one of the best things you can do for your carpet. Don’t forget to use the hose end or a small tool to vacuum the outer edge of any carpeted stairs you may have. The soil really gets impacted in this area from traffic and most people just vacuum the top of the tread area. Eventually however, vacuuming will not be enough to maintain the carpet. The problem is that over time, an oily film builds on the carpet. This can come from pollution, moisture and cooking oils in the air, perspiration from bare feet, etc. Another big source of oily film is pets; they have oily coats and they sweat from their feet (I know, I have three large dogs!). Now it’s not that this oily film in itself looks dirty, but what happens is that all the dust and dirt we all have sticks to the oil and therefore to the carpet. At this point, your vacuum can no longer remove it and you must have it cleaned to remove the oil and dirt. The good news is that the cleaning method and products that we use are the very best at removing the oily film and soil. Q: How often should I have my carpets cleaned? A: Well, I would like to give you two answers here. First, I must tell you that you should have it professionally cleaned at least every 12 to 24 months. One reason I say this is that most carpet manufacturers require this to maintain the warranty on your carpet. They do this because soil and grit in the carpet is the major cause of carpet damage and  most carpet manufacturers recommend. If you have never seen others do it, a combination wand is used to inject a cleaning chemical into the carpet under high pressure. It then takes maybe a tenth of a second to break down and mix with the dirt and stains before powerful vacuums suck it out. As a system, nothing removes more dirt. 
Truck mounted carpet cleaning equipment minimizes noise in the room being cleaned, but truck mounted carpet cleaning equipment may cause noise and air pollution offensive to neighbors, and may violate anti-idling bylaws in some jurisdictions. However, truck-mounted cleaning is much faster than portable equipment, and extra heat and power can give faster drying times. A Rug Doctor rental carpet cleaning machine. A common process of hot water extraction [1] begins with preconditioning. Alkaline agents such as ammonia solution for synthetic carpets, or acidic solution (such as vinegar solution) for woolen carpets, are sprayed into the carpet, then agitated with a grooming brush or an automatic scrubbing machine. Next, a pressurized manual or automatic cleaning tool (such as a wand) passes over the surface to rinse out all pre-conditioner, residue, and particulates. If an alkaline detergent is used on a woolen fibre, use of an acetic acid solution will restore neutral fiber pH. The acid rinse thus neutralizes the alkaline residues, and can contribute to softening cleaned fabrics.[2] The hot water extraction method is the preferred method of many carpet manufacturers.[citation needed] Extraction is, by far, the most important step in the hot water extraction process. Since the hot-water extraction method uses much more water than other methods like bonnet or shampoo cleaning, proper extraction and air flow are critical to avoid drying issues. Drying time may also be decreased by extra use of fans, air conditioning, and/or outdoor ventilation.[3] Older surfaces, such as double jute-backed carpets and loose rugs with natural foundation yarns, could shrink after a wet treatment, leading to suppositions that wet-cleaning could also remove wrinkles.[citation needed] However, this notion is antiquated and this method could also occasionally tear seams or uproot strips.[citation needed] Newer carpets, such as with synthetic backing and foundation yarns, do not shrink, and they smooth easily; in such carpets, wrinkles indicate an underlying problem, such as adhesive, that may need a certified carpet inspector to determine.[4] Wet-cleaning systems naturally require drying time, which may lead to concerns about very slow drying, the risk of discoloration returning during drying, and odors, bacteria, fungi, molds, and mildews. Carpet cleaning specialists try to find a balance between rapid drying (attributable to lower flow rate through the cleaning jets of a spray system) and the need to remove the most soil (attributable to higher flow rate).[3] Pretreatments similar to those in dry-cleaning and "very low moisture" systems are employed, but require a longer dwell time of 15 to 20 minutes, because of lower amounts of carpet agitation. Ideal pretreatments should rinse easily and leave dry, powdery, or crystalline residue that can be flushed without contributing to re-soiling.[2] Dry-cleaning[edit] For more details on this topic, see Dry carpet cleaning. Many dry carpet-cleaning systems rely on specialized machines. 
These systems are mostly "very low moisture" (VLM) systems, relying on dry compounds complemented by application cleaning solutions, and are growing significantly in market share due in part to their very rapid drying time,[3] a significant factor for 24-hour commercial installations. Dry-cleaning and "very low moisture" systems are also often faster and less labor-intensive than wet-extraction systems. Heavily soiled areas require the application of manual spotting, pretreatments, preconditioners, and/or "traffic-lane cleaners", (commonly sprayed onto carpet prior to the primary use of the dry-cleaning system) which are detergents or emulsifiers which break the binding of different soils to carpet fibers over a short period of time. For example, one chemical may dissolve the greasy films that bind soils to the carpet, and thus prevent effective soil removal through vacuuming. The solution may add a solvent like d-limonene, petroleum byproducts, glycol ethers, or butyl agents. The amount of time the pretreatment dwells in the carpet should be less than 15 minutes, due to the thorough carpet brushing common to these "very low moisture" systems, which provides added agitation to ensure the pretreatment works fully through the carpet.[2] The benefit of dry carpet cleaning, over wet solutions, is that dry chemical compounds don't attract dirt, like dried shampoo.[citation needed] While dry carpet cleaning is more expensive and more time consuming to clean than Bonnet or extraction, dry cleaning formulas put less stress on the carpets themselves.[citation needed] Dry compound[edit] This section does not cite any sources. Please help improve this section by adding citations to reliable sources. Unsourced material may be challenged and removed. (March 2015) (Learn how and when to remove this template message) A 98% biodegradable or others,[5] slightly moist absorbent cleaning compound may be spread evenly over carpet and brushed or scrubbed in. For small areas, a household hand brush can work such a compound into carpet pile; working like "tiny sponges", the attracted cleaning solution dissolve dirt, dirt and grime is attracted/absorbed to the compound, after a short drying time (the cleaning solution which is attracted to the compound must evaporate), it will be removed with a vacuum cleaner, the drier the better, leaving carpet immediately clean and dry. But it's very difficult to remove all residues, the residues can cause allergies and biological compounds may cause discolourations on carpets. For commercial applications, a specially designed cylindrical counter-rotating brushing system is used, without a vacuum cleaner. Machine scrubbing is more typical, in that hand scrubbing generally cleans only the top third of carpet. Encapsulation[edit] In the 1990s, new polymers began literally encapsulating (crystallizing) soil particles into dry residues on contact.[6] In the conventional cleaning process surfactant molecules attach themselves to oily soil particles, suspending them (emulsification) so that they can be easily rinsed away. Surfactant (detergent) molecules and emulsified soils which escape being rinsed away, remain in the fibre and continue to attract soiling, causing the condition of the carpet to degenerate; often re-soiling faster than before it was subjected to the cleaning process. Encapsulators are speciality detergent polymers which become part of the detergent system. As drying occurs (20-30 min. drytime), after cleaning, these encapsulators bind the detergent molecules and residual soils in a brittle, crystalline structure.[5] Detergent and soil particles can no longer attract other soils and are easily removed by dry vacuuming. In addition to binding the detergent and soil residues the encapsulation chemistry coats the clean fibre with the same brittle film. This reduces the fibre’s affinity for oily and particulate soils. As this brittle film"breaks away" and more soil is removed, the appearance of the fibre improves as opposed to soiling more rapidly. Products which also employ fluorochemical technology, display dramatically extended anti re-soiling time periods. Cleaning solution is applied by rotary machine, brush applicator, or compression sprayer. 
Dry residue is vacuumable immediately (20-30 min. drytime), either separately or from a built-in unit of the cleaning-system machine. According to ICS Cleaning Specialist, evidence suggests encapsulation improves carpet appearance, compared to other systems; and it is favorable in terms of high-traffic needs, operator training, equipment expense, and lack of wet residue. Encapsulation carpet cleaning also keeps carpets cleaner for longer periods of time compared to other methods. Encapsulation also avoids the drying time of carpet shampoos, making the carpet immediately available for use. The use of encapsulation to create a crystalline residue that can be immediately (20-30 min. drytime) vacuumed (as opposed to the residue of wet cleaning systems, which generally requires an additional day before vacuuming) is a newer technology that has recently become an accepted method for commercial and residential deep cleaning.[4] Bonnet[edit] This section does not cite any sources. Please help improve this section by adding citations to reliable sources. Unsourced material may be challenged and removed. (March 2015) (Learn how and when to remove this template message) After club soda mixed with cleaning product, other products are also possible, is deposited onto the surface as mist, a round buffer or "bonnet" scrubs the mixture with rotating motion. This industry machine resembles a floor buffer, with an absorbent spin or oscillating pad that attracts soil and is rinsed or replaced repeatedly. The bonnet method is not strictly dry-cleaning and involves significant drying time. To reduce pile distortion, the absorbent bonnet should be kept well-lubricated with cleaning solution. Its not recommended to dunk the bonnet in a bucket of cleaning solution and then wring it out with a mop-bucket wringer, then the bonnet is to wet. Its very important to change or turn the bonnet early, Bonnets can become filled with soil in just a couple hundred square feet. And once loaded with soil, the bonnet will not hold any more; instead, it simply moves the soil from one area to another. The overly wet bonnet also deposits residues that attract soils when they are dry, creating the need to clean more often. Its recommended for robust and not for high floor carpet, it swirls the floor. It distorts pile and grinds dirt deeper in carpet fiber also it has an abrasive effect.[7] When there is a large amount of foreign material in the carpet, extraction with a wet process may be needed. Normally, the spin-bonnet method may not be as capable of sanitizing carpet fibers due to the lack of hot water, for this a spezial thermo machine is needed, here the buffing machine is equipped with a heating, to heat up the bonnet, but a post-cleaning application of an antimicrobial agent is used to make up for this. Compared to steam cleaning, the small amounts of water required with spin-bonnet carpet cleaning favor water-conservation considerations. It only cleans the top of the carpet 1/8 inch but its very fast for wide areas. But bonnet cleaning is not the best mechanism for completely removing the chemical that is pre-sprayed onto a carpet. Its recommended that only surfactant free or encapsulating products are used. On the other hand, the re-soiling is great. Shampoo[edit] Wet shampoo cleaning with rotary machines, followed by thorough wet vacuuming, was widespread until about the 1970s, but industry perception of shampoo cleaning changed with the advent of encapsulation. Hot-water extraction, also regarded as preferable, had not been introduced either. Wet shampoos were once formulated from coconut oil soaps;[4] wet shampoo residues can be foamy or sticky, and steam cleaning often reveals dirt unextracted by shampoos. Since no rinse is performed, the powerful residue can continue to collect dirt after cleaning, leading to the misconception that carpet cleaning can lead to the carpet getting "dirtier faster" after the cleaning.[4][6]
 The best method is to combine shampoo and extraction, first shampoo with a spin brush to loosen the dirt and the pile, then extraction the carpet. But this needs time and double rinsed is necessary and the drying time is up to 24 h. When wet-shampoo chemistry standards converted from coconut oil soaps to synthetic detergents as a base, the shampoos dried to a powder, and loosened dirt would attach to the powder components, requiring vacuuming by the consumer the day after cleaning.[4] Dry foam carpet cleaning[edit] This section does not cite any sources. Please help improve this section by adding citations to reliable sources. Unsourced material may be challenged and removed. (March 2015) (Learn how and when to remove this template message) Dry foam cleaning[8] involves applying cleaning foam and immediately vacuuming the foam. It is not a completely dry method since the foam is 90% air and 10% liquid. A dry foam machine consists of a pressure tank in which a solution of water and shampoo is added. This method is used for water sensitive carpets, needle felt, and other carpet types whose construction inhibits sufficient water extraction. Vacuum wash[edit] This section does not cite any sources. Please help improve this section by adding citations to reliable sources. Unsourced material may be challenged and removed. (March 2015) (Learn how and when to remove this template message) Vacuum washing[9] employs a washhead that sprays water without detergent and immediately removes it by suction, creating a swirl of water. This ensures high cleaning performance, extracting the dirt from the carpet to a depth of half inch. By immediately reabsorbing the wash water, the drying time greatly shortened. This method is suitable for intermediate and basic cleaning. Because it does not require cleaning products, it leaves no detergent residue. 

 

Red Deer Carpet Cleaners

Red Deer Carpet Cleaners

Red Deer Carpet Cleaning

Red Deer Carpet Cleaning